 | | Mechanics of Solids
A Journal of Russian Academy of Sciences | | Founded
in January 1966
Issued 6 times a year
Print ISSN 0025-6544
Online ISSN 1934-7936 |
Archive of Issues
| Total articles in the database: | | 12854 |
| In Russian (Èçâ. ÐÀÍ. ÌÒÒ): | | 8044
|
| In English (Mech. Solids): | | 4810 |
|
| << Previous article | Volume 57, Issue 6 / 2022 | Next article >> |
| Bing-Zhang Xue, Jian-Wei Li, Rui Huang, Yao-Zong Yang, Hua-Shuai Gong, Qi-Ming Zhang, Ling-Hao Kong, and D.M. Li, "A study of Negative Poisson's Ratio of 3D Printed Auxetic Structures," Mech. Solids. 57 (6), 1524-1533 (2022) |
| Year |
2022 |
Volume |
57 |
Number |
6 |
Pages |
1524-1533 |
| DOI |
10.3103/S0025654422060139 |
| Title |
A study of Negative Poisson's Ratio of 3D Printed Auxetic Structures |
| Author(s) |
Bing-Zhang Xue (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China)
Jian-Wei Li (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China)
Rui Huang (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China)
Yao-Zong Yang (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China; State Key Laboratory of Disaster Prevention & Mitigation of Explosion & Impact, Army Engineering University of PLA, Nanjing, 210007 China)
Hua-Shuai Gong (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China; College of Naval Architecture and Ocean Engineering, Naval University of Engineering, Wuhan, 430033 China)
Qi-Ming Zhang (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China)
Ling-Hao Kong (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China, NonlineLab_WHUT@163.com)
D.M. Li (School of Civil Engineering and Architecture, Wuhan University of Technology, Wuhan, 430070 China) |
| Abstract |
In this paper, the characteristics of negative Poisson’s ratio with the re-entrant hexagonal honeycomb structures using photocuring 3D printing are studied experimentally. The experimental results are compared with the corresponding linear elastic analytical solutions and finite element simulation results, respectively. The results of the two methods fit well with the experimental results. In the small deformation stage, the behavior of the re-entrant hexagonal honeycomb structures with negative Poisson's ratio is completely consistent with the analytical and numerical results. However, in the large deformation stage, the curves of experiment with negative Poisson's ratio gradually deviate from the curves of linear elastic analytical solution and figures are less than the linear elastic analytical solutions, but the characteristic of negative Poisson's ratio is also stable. The experimental values of Poisson's ratio in the whole tensile stage are consistent with the numerical solutions. On this basis, we further studied the influence of the rod size and structural thickness on the structural Poisson's ratio, and found that the thickness of the structures has basically no effect on the Poisson's ratio, but the values of Poisson’s ratio increase with the increase of the size of the rods. |
| Keywords |
auxetic mechanical metamaterials, negative Poisson's ratio, 3D printing, finite element analysis, re-entrant honeycomb structures |
| Received |
29 July 2022 | Revised |
19 August 2022 | Accepted |
19 August 2022 |
| Link to Fulltext |
|
| << Previous article | Volume 57, Issue 6 / 2022 | Next article >> |
|
 If you find a misprint on a webpage, please help us correct it promptly - just highlight and press Ctrl+Enter
|
|
Russian 
English